PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
Image Name: Linux-2.6.31.8
Created: 2011-09-28 19:09:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080956 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00800000 …
Image Name: Linux-2.6.31.8
Created: 2011-09-28 19:09:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080956 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
OK
Starting kernel …
Uncompressing Linux……………………………………………………………………………………………………………………. done, booting the kernel.
[ 0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Ignoring unrecognised tag 0x41004345
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80×30
[ 0.000000] Calibrating delay loop… 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] Feroceon L2: Enabling L2
[ 0.230000] Feroceon L2: Cache support initialised.
[ 0.230000]
[ 0.230000] CPU Interface
[ 0.230000] ————-
[ 0.230000] SDRAM_CS0 ….base 00000000, size 128MB
[ 0.230000] SDRAM_CS1 ….disable
[ 0.230000] SDRAM_CS2 ….disable
[ 0.230000] SDRAM_CS3 ….disable
[ 0.230000] PEX0_MEM ….base e0000000, size 128MB
[ 0.230000] PEX0_IO ….base f2000000, size 1MB
[ 0.230000] PEX1_MEM ….no such
[ 0.230000] PEX1_IO ….no such
[ 0.230000] INTER_REGS ….base f1000000, size 1MB
[ 0.230000] NFLASH_CS ….base fa000000, size 2MB
[ 0.230000] SPI_CS ….base f4000000, size 16MB
[ 0.230000] BOOT_ROM_CS ….no such
[ 0.230000] DEV_BOOTCS ….no such
[ 0.230000] CRYPT_ENG ….base f0000000, size 2MB
[ 0.230000]
[ 0.230000] Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)– RD-88F6192A-NAS Soc: 88F6192 A1 LE
[ 0.230000]
[ 0.230000] Detected Tclk 166666667 and SysClk 200000000
[ 0.230000] Marvell USB EHCI Host controller #0: c403e740
[ 0.730000] PEX0 interface detected Link X1
[ 0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 0.740000] pci 0000:00:01.0: PME# disabled
[ 0.740000] PCI: bus0: Fast back to back transfers disabled
[ 0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 0.750000] bio: create slab at 0
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.750000] TCP reno registered
[ 0.750000] NET: Registered protocol family 1
[ 0.750000] cpufreq: Init kirkwood cpufreq driver
[ 0.760000] XOR registered 4 channels
[ 0.760000] XOR 2nd invalidate WA enabled
[ 0.760000] cesadev_init(c000d7fc)
[ 0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.770000] msgmni has been set to 231
[ 0.770000] alg: No test for cipher_null (cipher_null-generic)
[ 0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 0.770000] alg: No test for digest_null (digest_null-generic)
[ 0.770000] alg: No test for compress_null (compress_null-generic)
[ 0.780000] alg: No test for stdrng (krng)
[ 0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[ 0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.790000] io scheduler noop registered
[ 0.790000] io scheduler anticipatory registered (default)
[ 0.790000] Initializing ths8200_init
[ 0.790000] Initializing dove_adi9889_init
[ 0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.810000] console [ttyS0] enabled
[ 0.820000] Integrated Sata device found
[ 0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[ 0.850000] scsi0 : Marvell SCSI to SATA adapter
[ 0.860000] scsi1 : Marvell SCSI to SATA adapter
[ 0.870000] Loading Marvell Ethernet Driver:
[ 0.870000] o Cached descriptors in DRAM
[ 0.880000] o DRAM SW cache-coherency
[ 0.880000] o 1 Giga ports supported
[ 0.880000] o Single RX Queue support – ETH_DEF_RXQ=0
[ 0.890000] o Single TX Queue support – ETH_DEF_TXQ=0
[ 0.890000] o TCP segmentation offload (TSO) supported
[ 0.900000] o Large Receive offload (LRO) supported
[ 0.900000] o Receive checksum offload supported
[ 0.910000] o Transmit checksum offload supported
[ 0.910000] o Network Fast Processing (Routing) supported – (Disabled)
[ 0.920000] o Driver ERROR statistics enabled
[ 0.930000] o Proc tool API enabled
[ 0.930000] o SKB Reuse supported – (Disabled)
[ 0.930000] o SKB Recycle supported – (Disabled)
[ 0.940000] o Rx descripors: q0=128
[ 0.940000] o Tx descripors: q0=532
[ 0.950000] o Loading network interface(s):
[ 0.950000] o register under mv88fx_eth platform
[ 0.960000] o eth0, ifindex = 2, GbE port = 0
[ 0.960000]
[ 0.960000] mvFpRuleDb (c45b1000): 1024 entries, 4096 bytes
[ 0.970000] Counter=0, opIdx=6, overhead=16
[ 0.970000] Counter=1, opIdx=2, overhead=0
[ 0.980000] Counter=2, opIdx=1, overhead=18
[ 0.980000] Counter=3, opIdx=2, overhead=0
[ 0.990000] tun: Universal TUN/TAP device driver, 1.6
[ 0.990000] tun: (C) 1999-2004 Max Krasnyansky
[ 1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.010000] Scanning device for bad blocks
[ 1.060000] Using static partition definition
[ 1.060000] Creating 5 MTD partitions on “nand_mtd”:
[ 1.070000] 0x000000000000-0x000000200000 : “u-boot”
[ 1.070000] 0x000000200000-0x000000500000 : “uImage”
[ 1.080000] 0x000000500000-0x000000800000 : “uImage2”
[ 1.080000] 0x000000800000-0x000001000000 : “failsafe”
[ 1.090000] 0x000001000000-0x000008000000 : “root”
[ 1.100000] UBI: attaching mtd4 to ubi0
[ 1.100000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.110000] UBI: logical eraseblock size: 126976 bytes
[ 1.110000] UBI: smallest flash I/O unit: 2048
[ 1.120000] UBI: sub-page size: 512
[ 1.120000] UBI: VID header offset: 2048 (aligned 2048)
[ 1.130000] UBI: data offset: 4096
[ 1.350000] UBI: attached mtd4 to ubi0
[ 1.360000] UBI: MTD device name: “root”
[ 1.360000] UBI: MTD device size: 112 MiB
[ 1.360000] UBI: number of good PEBs: 896
[ 1.370000] UBI: number of bad PEBs: 0
[ 1.370000] UBI: max. allowed volumes: 128
[ 1.380000] UBI: wear-leveling threshold: 4096
[ 1.380000] UBI: number of internal volumes: 1
[ 1.390000] UBI: number of user volumes: 1
[ 1.390000] UBI: available PEBs: 0
[ 1.400000] UBI: total number of reserved PEBs: 896
[ 1.400000] UBI: number of PEBs reserved for bad PEB handling: 8
[ 1.410000] UBI: max/mean erase counter: 1/0
[ 1.410000] UBI: image sequence number: 0
[ 1.420000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 1.420000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.430000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.440000] UBI: background thread “ubi_bgt0d” started, PID 452
[ 1.470000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.490000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[ 1.490000] usb usb1: configuration #1 chosen from 1 choice
[ 1.500000] hub 1-0:1.0: USB hub found
[ 1.500000] hub 1-0:1.0: 1 port detected
[ 1.510000] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 1.510000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 1.520000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
[ 1.530000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[ 1.540000] usb usb2: configuration #1 chosen from 1 choice
[ 1.540000] hub 2-0:1.0: USB hub found
[ 1.550000] hub 2-0:1.0: 4 ports detected
[ 1.550000] Initializing USB Mass Storage driver…
[ 1.550000] usbcore: registered new interface driver usb-storage
[ 1.560000] USB Mass Storage support registered.
[ 1.570000] usbcore: registered new interface driver ums-datafab
[ 1.570000] usbcore: registered new interface driver ums-freecom
[ 1.580000] usbcore: registered new interface driver ums-jumpshot
[ 1.580000] usbcore: registered new interface driver ums-sddr09
[ 1.590000] usbcore: registered new interface driver ums-sddr55
[ 1.600000] usbcore: registered new interface driver ums-usbat
[ 1.600000] mice: PS/2 mouse device common for all mice
[ 1.610000] i2c /dev entries driver
[ 1.620000] sdhci: Secure Digital Host Controller Interface driver
[ 1.620000] sdhci: Copyright(c) Pierre Ossman
[ 1.630000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection
[ 1.640000] usbcore: registered new interface driver usbhid
[ 1.640000] usbhid: v2.6:USB HID core driver
[ 1.650000] TCP cubic registered
[ 1.650000] NET: Registered protocol family 17
[ 1.660000] RPC: Registered udp transport module.
[ 1.660000] RPC: Registered tcp transport module.
[ 1.670000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.740000] UBIFS: recovery needed
[ 1.810000] UBIFS: recovery completed
[ 1.820000] UBIFS: mounted UBI device 0, volume 0, name “rootfs”
[ 1.820000] UBIFS: file system size: 110850048 bytes (108252 KiB, 105 MiB, 873 LEBs)
[ 1.830000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 1.840000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.840000] UBIFS: default compressor: lzo
[ 1.850000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.850000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.860000] Freeing init memory: 124K
[ 4.230000] eth0: started
udhcpc (v1.16.1) started
HWADDR 00 0x25 0x31 0x04 0x12 0x05
PIP0 18
PIP1 5
cat: can’t open ‘/etc/resolv.conf’: No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover…
Sending discover…
Sending discover…
HWADDR 00 0x25 0x31 0x04 0x12 0x05
PIP0 18
PIP1 5
No lease, forking to background
Loading gpio_keys.ko…
Loading ejectbutton.ko…
[ 13.750000] IRQ 93 uses trigger mode 0; requested 3
[ 13.760000] input: gpio-keys as /devices/platform/gpio-keys.0/input/input0
[ 13.770000] xce_ebtn: Pogoplug series V4 eject button initialized.
[ 13.920000] ufsd: module license ‘Commercial product’ taints kernel.
[ 13.920000] Disabling lock debugging due to kernel taint
[ 13.950000] ufsd: driver (8.6 (U86_S[2012-02-28-18:39:23]), LBD=ON, delalloc, ioctl) loaded at bf00c000
[ 13.950000] NTFS support included
[ 13.950000] Hfs+/HfsX support included
[ 13.950000] For ‘CloudEngines_PogoPlug_2011-08-03’
Loading rt3070sta.ko: [ 14.280000] rtusb init rt2870 —>
[ 14.290000] usbcore: registered new interface driver rt2870
Success
Loading xce.ko: [ 14.320000] Cloud Engines XCE Init [Version: 3.9.0.4]
[ 14.320000] XCE: CPU MEMORY MAP:
[ 14.320000] XCE: — 0x00001000 – 0xbeffffff (3055 MB) User Space Mappings
[ 14.330000] XCE: — 0xbf000000 – 0xbfffffff ( 16 MB) Kernel module space
[ 14.340000] XCE: — 0xc0000000 – 0xc7ffffff ( 128 MB) Kernel direct-mapped ram
[ 14.350000] XCE: — 0xc8800000 – 0xe7ffffff ( 504 MB) Kernel vmalloc space
[ 14.350000] XCE: — 0xe8000000 – 0xfeffffff ( 367 MB) Kernel platform space
[ 14.360000] XCE: CPU FEATURES:
[ 14.360000] XCE: — I Cache: enabled
[ 14.370000] XCE: — D Cache: enabled
[ 14.370000] XCE: — Branch Predict: disabled
[ 14.380000] XCE: — MMU: enabled
[ 14.380000] XCE: — Alignment Abort: enabled
[ 14.390000] XCE: BLPARAMS: — Loading properties [c4be3efc].
[ 14.400000] XCE: BLPARAMS: — MTD @ [c45c0c00].
[ 14.400000] XCE: BLPARAMS: Locating parameter block…
[ 14.410000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 14.410000] XCE: Loaded Property Size: 2048
[ 14.420000] XCE: – ‘cesvcid’ -> ‘UGZRQL3K3BXDWQ7MVKDECX8MAE’
[ 14.420000] XCE: – ‘ceboardver’ -> ‘PPV4A3’
[ 14.430000] XCE: — ICache Prefetch: enabled
[ 14.430000] XCE: — DCache Prefetch: enabled
[ 14.440000] XCE: — L2 Cache: enabled
[ 14.440000] XCE: — L2 Prefetch: disabled
[ 14.450000] XCE: — L2 Writethrough: disabled
[ 14.450000] XCE: — Write Allocate: disabled
[ 14.460000] XCE: — Streaming: disabled
[ 14.460000] XCE: Current GPIO State:
[ 14.460000] XCE: GPIO L OUT: 0x01f18400
[ 14.470000] XCE: GPIO L OE: 0xfe004800
[ 14.470000] XCE: GPIO L BLINK: 0x00000000
[ 14.480000] XCE: GPIO L POL: 0x28000000
[ 14.480000] XCE: GPIO L IN: 0x11f00000
[ 14.480000] XCE: GPIO H OUT: 0x00000008
[ 14.490000] XCE: GPIO H OE: 0x00000005
[ 14.490000] XCE: GPIO H BLINK: 0x00000000
[ 14.500000] XCE: GPIO H POL: 0x00000000
[ 14.500000] XCE: GPIO H IN: 0x00000008
Success
Starting hbplug: Success
/ # [ 14.590000] XCE: BLPARAMS: — Loading properties [c4b7becc].
[ 14.600000] XCE: BLPARAMS: — MTD @ [c45c0c00].
[ 14.600000] XCE: BLPARAMS: Locating parameter block…
[ 14.610000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 14.620000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[ 14.620000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[ 14.630000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[ 20.000000] XCE: XCE: LED -> DISCONNECTED